- 1、本文档共5页,可阅读全部内容。
- 2、原创力文档(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。
- 3、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载。
- 4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
查看更多
研究开发复合中空热管冷凝侧传热特性崔腾飞 1,肖章平 1,曹马林
研究开发
复合中空热管冷凝侧传热特性
崔腾飞 1,肖章平 1,曹马林 2,张琳 1,蒋枫 1
(1 常州大学机械工程学院,江苏 常州 213016;2 泰州梅兰化工有限公司,江苏 泰州 321200)
摘要:复合中空热管能够有效解决普通重力热管换热设备的酸露点腐蚀问题,在回收低温烟气(200℃)余热
领域有重要的应用。建立了复合中空热管传热实验平台,对复合中空热管冷凝侧传热特性进行了实验研究。实 验所用热管管长 1080mm,不锈钢材质,工作介质为甲醇;热管蒸发侧和冷凝侧分别采用电加热和水冷却方式, K 型热电偶被用于测量管壁温度和冷却水进出口温度,真空压力传感器测量管内蒸气饱和压力;研究了充液率
(15%≤V+≤40%)和蒸发侧热流密度(9.48kW/m2≤q≤37.91kW/m2)对冷凝侧传热特性的影响。结果表明:当 充液率为 20%时,复合中空热管冷凝侧均温性能最好,冷凝侧换热系数最大,传热性能最佳;随着蒸发侧热流 密度的增大,复合中空热管有效冷凝长度增大,冷凝侧换热系数增大。实验研究为工业应用提供了基础。 关键词:复合中空热管;传热;充液率;热流密度
中图分类号:TK124
文献标志码:A
文章编号:1000–6613(2014)11–2868–05
DOI:10.3969/j.issn.1000-6613.2014.11.007
Experimental investigation of heat transfer characteristics of condensation
section in composite hollow heat pipe
CUI Tengfei1,XIAO Zhangping1,CAO Malin2,ZHANG Lin1,JIANG Feng1
(1School of Mechanical Engineering,Changzhou University,Changzhou 213016,Jiangsu,China;2 Taizhou Meilan
Chemical Co.,Ltd.,Taizhou 321200,Jiangsu,China)
Abstract:The composite hollow heat pipe can effectively solve the problem of acid dew corrosion of
heat exchanger equipment comprising ordinary gravity heat pipe,and has an important application in recycling waste heat of low temperature flue gas. A heat transfer experimental platform of composite
hollow heat pipe was established,and the heat transfer characteristics of condensation section were
investigated experimentally. A stainless steel tube of total length of 1080mm with methanol was studied. Electrical heating was used in the evaporation section and water cooling was used in the condensation section. Wall temperatures and inlet and outlet temperatures of cooling water were measured with K type thermocouples. Vapor saturation pressure in heat pipe was measured by vacuum pressure sensor.
The effect of two parameters : filling rate (15%≤V+≤40%) and evaporator heat flux
(9.48kW/m2≤q≤37.91kW/m2) on the heat transfer characteristics of condensation section were investigated. When filling rate was 20% , the composit
您可能关注的文档
- 多环芳烃的污染排放和控制趋势 课件.ppt
- 多基站调度网话务量模型.docx
- 多检测GPC技术在高分子表征中的应用.doc
- 多焦点IOL分析课件.ppt
- 多井型综合开发潜山裂缝性油藏.docx
- 多孔活性磷酸钙悬浮聚合分散剂的制备及性能研究.docx
- 多孔介质内原油渗流模型及数值计算.docx
- 多利有机生态农庄.docx
- 多联机机组与冷水风冷模块机组方案比较分析.doc
- 多联机室内机不同送风形式对室内环境的影响.docx
- 《GB/T 32151.42-2024温室气体排放核算与报告要求 第42部分:铜冶炼企业》.pdf
- GB/T 32151.42-2024温室气体排放核算与报告要求 第42部分:铜冶炼企业.pdf
- GB/T 38048.6-2024表面清洁器具 第6部分:家用和类似用途湿式硬地面清洁器具 性能测试方法.pdf
- 中国国家标准 GB/T 38048.6-2024表面清洁器具 第6部分:家用和类似用途湿式硬地面清洁器具 性能测试方法.pdf
- 《GB/T 38048.6-2024表面清洁器具 第6部分:家用和类似用途湿式硬地面清洁器具 性能测试方法》.pdf
- 《GB/T 18238.2-2024网络安全技术 杂凑函数 第2部分:采用分组密码的杂凑函数》.pdf
- GB/T 18238.2-2024网络安全技术 杂凑函数 第2部分:采用分组密码的杂凑函数.pdf
- 《GB/T 17215.686-2024电测量数据交换 DLMS/COSEM组件 第86部分:社区网络高速PLCISO/IEC 12139-1配置》.pdf
- GB/T 13542.4-2024电气绝缘用薄膜 第4部分:聚酯薄膜.pdf
- 《GB/T 13542.4-2024电气绝缘用薄膜 第4部分:聚酯薄膜》.pdf
文档评论(0)