- 1、本文档共36页,可阅读全部内容。
- 2、原创力文档(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。
- 3、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载。
- 4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
查看更多
模具设计与制造专业精品毕业论文--通用绕线架注塑模具的设计
PAGE
PAGE 30
内容提要
本设计主要讲述了以软聚氯乙烯(SPVC)为材料的线圈高骨架注塑模具的设计过程。
此模具在设计时,充分考虑了生产批量、以提高生产效率、降低生产成本为主要宗旨。
本产品为电动机绕线圈,形状规则,内空心,侧有凹槽,其要求它具有耐光,耐化学腐蚀、耐磨。结合这些要求,材料选择软聚氯乙烯。根据计算出的体积与质量选择SZ-100-60型号的注塑机注塑。由于塑件内空心,侧有凹槽要求模具必需采用斜导柱侧抽芯机构分型。经过比较,采用斜导柱在定模,哈夫块(斜滑块)在动模的结构 。整体斜楔定位,斜导柱侧抽芯分型,推板推出工件的工作原理。
设计中对主要零件一一的进行了设计。文中插入了非标准零件图,以及模具结构图。
Contents brief summary
Is it tell taking soft polyvinyl chloride (SPVC ) as material coil high skeleton mould plastics idea course of mould mainly to design originally.
This mould is in the design, fully consider production lot , regard improving production efficiency , reducing the production cost as the main aim.
This product winds the coil for the motor, form rule, hollow inside, the side has grooves , it requires it is able to bear all, able to bear chemistry and corroded, wear-resisting . Combine these require material choose the soft polyvinyl chloride. Choose the moulding plastics machine of SZ-100-60 type to mould plastics according to the volume and quality calculated out. Mould piece hollow , side have groove demand mould must adopt oblique to lead post side release the core organization dividing into type. Through compare, adopt oblique to lead post make mould , Haff piece (oblique to slip yuan ) Move the structure of the mould . Whole oblique wedge make a reservation, oblique to lead post side release core person who divide , push board put out operation principle of work piece.
To the designing one by one of major part in the design. Have inserted the non-standard part picture, and mould structure chart in the article.
目 录
内容摘要……………………………………………………………… = 1 \* ROMAN I
Contents brief summary…………………………………………… = 2 \* ROMAN II
前言…………………………………………………………………… 1
第1章 塑件分析………………………………………………… 2
第1.1节 塑件工艺性能分析……………………………………… 2
第1.2节 塑件批量………………………………………………… 2
第1.3节 塑件批量体量和质量…………………………………… 3
第2章 注塑机的选择…………………………………………… 4
第2.1节 注塑机的概述…………………………………………… 4
第2.2节 选择注塑机……………………………………………… 6
第3章 模具设计的有关计算…………………………………… 6
第3
您可能关注的文档
- 检察机关行政诉讼法律监督制度在立法层面的思考.doc
- 检察机关论文浅谈如何发挥检察机关中层干部的引领作用.doc
- 检察机关论文司法警察论文浅谈检察机关司法警察工作规范化建设的意义.doc
- 检查井支墩基坑支护方案.doc
- 检查梯防落梁吊篮安装作业指导书.doc
- 检查限位电缆等书面安全工作程序.doc
- 检测实验室仪器的期间核查.doc
- 检测实验室日常监督机制的控制点.doc
- 检验仪器,设备管理制度.doc
- 检验医学参考测量实验室的要求.doc
- 第十一章 电流和电路专题特训二 实物图与电路图的互画 教学设计 2024-2025学年鲁科版物理九年级上册.docx
- 人教版七年级上册信息技术6.3加工音频素材 教学设计.docx
- 5.1自然地理环境的整体性 说课教案 (1).docx
- 4.1 夯实法治基础 教学设计-2023-2024学年统编版九年级道德与法治上册.docx
- 3.1 光的色彩 颜色 电子教案 2023-2024学年苏科版为了八年级上学期.docx
- 小学体育与健康 四年级下册健康教育 教案.docx
- 2024-2025学年初中数学九年级下册北京课改版(2024)教学设计合集.docx
- 2024-2025学年初中科学七年级下册浙教版(2024)教学设计合集.docx
- 2024-2025学年小学信息技术(信息科技)六年级下册浙摄影版(2013)教学设计合集.docx
- 2024-2025学年小学美术二年级下册人美版(常锐伦、欧京海)教学设计合集.docx
文档评论(0)