- 1、本文档共46页,可阅读全部内容。
- 2、原创力文档(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。
- 3、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载。
- 4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
查看更多
摘 要
变速器是主要,其功能是改变传动比、改变驱动轮的扭矩和转动方向。因此变速器在车中得到广泛应用。 变速器设计Abstract.
Gearbox is the key part of the automobile. It is used to change the transmission ratio, torque and running direction of the driving wheel. It can change the vehicle speed and tyre torque in a big scope, cut off the power transfer from the engine, and also provides a reverse traveling direction for the vehicle. Therefore, the reasonability of the structure design of a transmission gearbox directly affects the vehicles dynamic performance. It is usually required shifting gears rapidly and conveniently, saving force, and having a higher working efficiency and low working noises.
This thesis designed a manual transmission gearbox of theEQ1090ruck. A scheme of structure with three shafts, 5+1shifts and synchronizer adopted here, Combine to pour to block wheel gear and stir fork to carry on a reasonable decoration .where the first and second shafts were arranged in line. This kind of structure reduces the gearbox dimension in the axis direction, In assurance block to count under the constant circumstance, decrease wheel gear number. therefore makes the designed transmission gearbox more compact.
Using the given basic parameters, it was firstly determined the transmission ratio of each shift, the shaft center distances, the gear modulus, the gear pressing angles and widths, and so on. And then the general dimension of the gearbox, including its length, width and height. The stresses of the intermediate shaft and the gears were validated by using both the calculator and a self-made MATLAB program. Finally,some engineering drawings were carried out.
The calculated results show: the determined dimensions and stresses of the designed gears and shafts satisfied the design requirements; the adopted structure is reasonable.
Key words: automobile;gearbox;design;synchronizer
目 录
第1章 绪 论 1
1.1变速器的简介 1
1.2变速器的功用 1
第2章 变速器设计方案及论证 3
2.1变速器的要求 3
2.2变速器的设计方法论证 3
第3章 变速器设计方案论证 5
3.1变速器基本参数的确定 5
3.1.1轴的直径的初步确定 5
3.2齿轮参
您可能关注的文档
- (毕业设计论文)《45m3h淀粉废水回收工段多效蒸发器的工艺设计》.doc
- (毕业设计论文)《45T旋挖钻机桅设计》.doc
- (毕业设计论文)《50T转炉动态炼钢控制系统》.doc
- (毕业设计论文)《51系列单片机教学实验板硬件设计》.doc
- (毕业设计论文)《51系列单片机实现AD9850DDS信号源的研制》.doc
- (毕业设计论文)《64位可重组加法单元设计》.doc
- (毕业设计论文)《64点温度监测与控制系统的设计》.doc
- (毕业设计论文)《75kt/a烧碱装置氯气处理工序工艺设计》.doc
- (毕业设计论文)《80T专用运煤敞车总体设计》.doc
- (毕业设计论文)《80吨级运煤专用敞车总体方案设计》.doc
文档评论(0)