- 1、本文档共29页,可阅读全部内容。
- 2、原创力文档(book118)网站文档一经付费(服务费),不意味着购买了该文档的版权,仅供个人/单位学习、研究之用,不得用于商业用途,未经授权,严禁复制、发行、汇编、翻译或者网络传播等,侵权必究。
- 3、本站所有内容均由合作方或网友上传,本站不对文档的完整性、权威性及其观点立场正确性做任何保证或承诺!文档内容仅供研究参考,付费前请自行鉴别。如您付费,意味着您自己接受本站规则且自行承担风险,本站不退款、不进行额外附加服务;查看《如何避免下载的几个坑》。如果您已付费下载过本站文档,您可以点击 这里二次下载。
- 4、如文档侵犯商业秘密、侵犯著作权、侵犯人身权等,请点击“版权申诉”(推荐),也可以打举报电话:400-050-0827(电话支持时间:9:00-18:30)。
查看更多
毕业论文外文翻译-S-422和RS-485应用
RS-422 and RS-485 application note
Chapter 1: Overview
Introduction
The purpose of this application note is to describe the main elements of an RS-422 and RS-485 system. This application note attempts to cover enough technical details so that the system designer will have considered all the important aspects in his data system design. Since both RS-422 and RS-485 are data transmission systems that use balanced differential signals, it is appropriate to discuss both systems in the same application note. Throughout this application note the generic terms of RS-422 and RS-485 will be used to represent the EIA/TIA-422 and EIA/TIA-485 Standards.
Data Transmission Signals
Unbalanced Line Drivers
Each signal that transmits in an RS-232 unbalanced data transmission system appears on the interface connector as a voltage with reference to a signal ground. For example, the transmitted data (TD) from a DTE device appears on pin 2 with respect to pin 7 (signal ground) on a DB-25 connector. This voltage will be negative if the line is idle and alternate between that negative level and a positive level when data is sent with a magnitude of ±5 to ±15 volts. The RS-232 receiver typically operates within the voltage range of +3 to +12 and -3 to -12 volts as shown in Figure 1.1.
Figure 1.1: RS-232 Interface Circuit
Balanced Line Drivers
In a balanced differential system the voltage produced by the driver appears across a pair of signal lines that transmit only one signal. Figure 1.2 shows a schematic symbol for a balanced line driver and the voltages that exist. A balanced line driver will produce a voltage from 2 to 6 volts across its A and B output terminals and will have a signal ground (C) connection. Although proper connection to the signal ground is important, it isnt used by a balanced line receiver in determining the logic state of the data line. A balanced line driver can also have an input signal called an “Enable” signal. The purpose of this signal is to connect th
您可能关注的文档
最近下载
- 《指向高中生物核心素养的大单元教学设计研究》课题研究方案.doc
- Unit 4 What can you do Part C Story time(课件)-人教PEP版英语五年级上册.pptx VIP
- 学生会权益部部门招新.pptx VIP
- 《22G101三维彩色立体图集》.pdf VIP
- 一种快速测定萤石中氟化钙含量的方法.pdf VIP
- 人教版六年级数学上册同步辅导讲义教师版.doc
- 2025高中英语外刊时文阅读 巴黎奥运会之全红婵和潜水介绍 课件.pptx
- 植物生理学-扬州大学-中国大学MOOC慕课答案.pdf
- 三论我国发展注气提高采收率技术-李士伦.ppt
- 人教版六年级数学上册同步辅导讲义.doc
文档评论(0)